CP696 electronic batch counter

30 Years of serving the Industrial Controls market --- Design, manufacturing and Sourcing of all your control requirements

people counters, people counting, hand held tachometers, electronic counters, digital timers, plug in timers, proximity sensors, shaft encoders, level control, large digital display, digital panel meters, signal conditioning, electronic timers, timing relays, batch counters, totalizing counters, totalising counters, dpm, sensors, photoelectric, capacitive, inductive, photoelectric, encoder, signal conversion, ratemeter, incremental encoder, decade boxes, resistance substitution box, capacitance substitution box, data display, rs485, rs232, custom electronics, system designsystem designcustom electronicsrs232rs485data displaycapacitance substitution boxresistance substitution boxdecade boxesincremental encoderratemetersignal conversionencoderphotoelectricinductivecapacitivephotoelectricsensorsdpmtotalising counterstotalizing countersbatch counterstiming relayselectronic timerssignal conditioningdigital panel meterslarge digital displaylevel controlshaft encodersproximity sensorsplug in timerselectronic countersdigital timershand held tachometerspeople countingpeople counters

[UP] [PRODUCTS] [HOME]

CP696 6 decade digital batch counter

View Datasheet

	96 x 96 mm DIN standard Housing
	Count up or down
	5 Amp changeover relay output
	1 Amp NPN transistor output
	115/230VAC or 12-28VDC supply
	12VDC output for proximity sensors etc
	Electronic count rate to 2.5Khz
	Contact count rate 30Hz
	Non Volatile Memory
	NPN or PNP type inputs
	Single shot or cycle modes
	Prescaler option.

Mode of Operation: This counter is programmed using the panel push switches to set the batch size and a 4 way switch at the rear to set the modes.

Single shot Mode - Up count: Pulses are counted from zero until the batch size is reached then the relay is energised. The count will continue if more pulses are applied to the input but the relay remains energised until the counter is reset.

Single shot Mode - Down count: The count is preset to the batch size and counts down to zero then the relay is energised. The count will remain at zero and the relay remains energised until the counter is reset.

Cycle Mode - Up count: Pulses are counted from zero until the batch size is reached then the relay is energised and the counter is reset and continues to count. The relay remains energised for a period that can be set between 0.1 and 5 seconds.

Cycle Mode - Down count: The count is preset to the batch size and counts down to zero then the relay is energised and the counter is reset to the preset value and continues to count. The relay remains energised for a period that can be set between 0.1 and 5 seconds.

Prescaler Option {order code PS} [Click here for details]

BCD output Option {order code BCD} [Click here for details]

RS232/485 Output Option {order code RS232 or RS485} [Click here for details]

Specification

Modes:	cycle/single-shot
Count direction:	up or down
Setting:	Push-Push switches
Inputs:	Reset, Pulse, Up-down select
Input type:	Selectable for PNP or NPN type sensors or volt free contact
Relay output:	Single pole changeover contacts - 5 amp at 240VAC or 30VDC
Transistor output:	NPN open collector rated at 1A @ 30 VDC
Supply:	115/240 VAC or 12 - 30 VDC
Power output:	12 volt DC output @ 50mA for powering sensors etc.
Housing:	96 mm x 96 mm DIN standard panel mounting plastic
Dimensions:	96 x 96 x 134 mm
Panel Cutout:	92 x 92 mm
Connections:	Rising cage screw terminals
Order code:	{type}{option 1}{option 2} i.e. CP672-PS, CP672-RS232

[UP] [PRODUCTS][HOME]

Send mail to info@abtekcontrols.com with questions or comments about this web site. Copyright � 2011 Abtek Controls Ltd

Send mail to info@abtekcontrols.com with questions or comments about this web site.
Copyright � 2011 Abtek Controls Ltd